- Replacing '87 Transmission and T case with an '86 (3 replies)
- 92 D50 2.4L hole in block (11 replies)
- "Diode relay" (5 replies)
- Banging valve...and now... (30 replies)
- 1985 D50 2.0 Timing Belt. (32 replies)
- No start: Ignition Switch or Solenoid? (25 replies)
- No oil pressure? (4 replies)
- auto transmission (1 replies)
- Transmission Infomation (5 replies)
- Pulling the A/C. (4 replies)
- how to set the base timing on a 3.0 v6 (1 replies)
- Stuck in Gear (32 replies)
- radiator (3 replies)
- Jet valve question (4 replies)
- TPS replacement on 94 2.4 (5 replies)
- 86 Ram 50 Transmission Questions (Automatic) (17 replies)
- Oil and fuel (0 replies)
- '89 Ram50 motor (11 replies)
- coolant in oil pan? (2 replies)
- quick weber question! (6 replies)
- looking for the two front cover bolts (2 replies)
- Are the 2.0l and the 2.6l interchangeable? (5 replies)
- quick question about electric fuel pumps (5 replies)
- Cheap place to replacement heater motor? (7 replies)
- how many head bolts in the 2.6? (3 replies)
- Oil Pan from 2wd to 4wd (0 replies)
- 1988 mighty max 2.0 (1 replies)
- i need help! trying to change my head gasket (11 replies)
- timing belt... (8 replies)
- HELP I'm confused (10 replies)
- do i need to take off the rocker arms for this (2 replies)
- Rear Main Seal (5 replies)
- 2.4L MM exhaust manifold???!!!! (6 replies)
- Stock Spark Plugs (2 replies)
- Need a clock retaining clip. (0 replies)
- 4G64 differences?! (5 replies)
- problem after problem/: (4 replies)
- Mechanical Fuel Pump psi? (2 replies)
- need torque specs for rods and crank (2 replies)
- Vacuum advance after weber install (1 replies)
- Need Help With Locating Gauge Fuse!! (11 replies)
- Occasional no start issue (25 replies)
- 2.4 efi engine surging (8 replies)
- Cylinder Head resources (7 replies)
- dodge stealth v-6 swap QUESTIONS (5 replies)
- transmission issue/: (12 replies)
- WHY Me???? (3 replies)
- StarQuest Parts (0 replies)
- gas tank interchange? (6 replies)
- Electric Fuel Pump Location (7 replies)
- Tuning up !! (0 replies)
- Need MSD help...FAST! (14 replies)
- Carb problems (6 replies)
- I gotta knock, and I figured out why. (6 replies)
- gas tank (8 replies)
- just bought 84 ram 50--????what engine do i have??? (6 replies)
- 2.6L Information (10 replies)
- Timing Question on a 2.0 (15 replies)
- AC compatability (3 replies)
- i gotta ac problem /: (30 replies)
- tach cluster (5 replies)
- Cold air intake or perfomance carb? (12 replies)
- HORRIBLE ping... (3 replies)
- Degreeing a Cam (1 replies)
- Alright, I'm stumped (4 replies)
- 5 Speed Trans (5 replies)
- fuel fitler (4 replies)
- New Clutch Old Problem Still 1987 Ram 50 4xr (6 replies)
- 63b? (3 replies)
- need help!!! need belt tensioner (2 replies)
- Fuel Injection on a 2.0 Liter (1 replies)
- Clutch: Change Cable to Hydrolic/ (2 replies)
- Clutch Hard to Depress on 87 Dodge Ram 50 (11 replies)
- Headers (3 replies)
- AC Condenser (1 replies)
- Heater (9 replies)
- flex plate/torque converter compatability (10 replies)
- Dodge power ram 50 2.6 gasser RPM range (2 replies)
- Loose Shifter (14 replies)
- AFtermarket Tach (26 replies)
- After-market Cruise Controls? (13 replies)
- ECU replacement (9 replies)
- Scratched cylinder wall (10 replies)
- overheating??? (15 replies)
- Installed new performance head! But... (12 replies)
- Radiator Foam (4 replies)
- the infamous rough idle question!! (10 replies)
- Roller Rocker assembly? (5 replies)
- Vibration after timing belt replaced (12 replies)
- fan shroud ? (13 replies)
- ticking valves (31 replies)
- 89 Dodge D50 Longbox 155.9 CID Automatic (19 replies)