Page 2 of 2 FirstFirst 12
Results 26 to 38 of 38

Thread: My Electric fuel pump install

  1. #26

    Array
    Status
    Offline
    Join Date
    04-03-2014
    Posts
    50
    Location

    CR, IA
    Vehicle

    1995 Mitsubishi Mighty Max
    Engine

    4G64
    Do you need to do the fuel pump for a 95?? Or is it just for the Carb'd engines?

  2. #27

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    6,059
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    Was wondering - did you need to restrict pressure from the Carter pump to run the weber? I have a Carter that I wasn't going to use on my L200 but I might consider it once I simplify the throttle linkage set up on the 32/36 I have (it had a swiss cheese wheel with an arm tack welded to it - just horrid...)

  3. #28

    Array
    Status
    Offline
    Join Date
    08-11-2012
    Posts
    1,199
    Location

    Oakland, CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    G63B
    Quote Originally Posted by Jeb View Post
    Do you need to do the fuel pump for a 95?? Or is it just for the Carb'd engines?
    No. Just get an FI fuel tank.

    Geezer, the Carter pump doesn't need a pressure regulator because it pumps at 2-4 PSI, which is what the Weber wants. But you can burn it out if it's not installed within 2 feet of the tank and it's not on a relay. You also want some kind of low oil pressure kill switch so it doesn't pump whenever the key is on in case of an accident. Check out the stickied Weber conversion thread in Performance Mods. There's a great diagram for how to wire it up safely.

  4. #29

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    6,059
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    O.k. Looks like I have some homework to do then

  5. #30

    Array
    Status
    Offline
    Join Date
    02-12-2015
    Posts
    6
    Location

    Joplin, Mo
    Vehicle

    1988 Mitsubishi Mighty Max
    Engine

    G54B
    I know this is an old post but wasn't sure where to ask this. When you remove the old pump after installing an electric did you make or buy the block off plate? If you bought the plate, do you know where I could find one? Thanks

  6. #31

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    6,059
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    I've made block off plates before out of scraps of alu sheet metal. They are easy enough to make. I haven't seen an aftermarket fuel pump block off plate and I don't know if there's a unit that can be used as a substitute. I did see EGR block off plates to suit our engines (pretty cheap too)

  7. #32




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,851
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    there is a thread on here where someone bought a fuel pump block off plate for a small block chevy that fit perfectly. It is easy to make one, just use the spacer as the template.
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  8. #33

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    6,059
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    Quote Originally Posted by pennyman1 View Post
    there is a thread on here where someone bought a fuel pump block off plate for a small block chevy that fit perfectly. It is easy to make one, just use the spacer as the template.
    I have a feeling that the SBC block off is viable for the G54B (gasket looks about the same) No such luck with the G63B

  9. #34




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,851
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    true - that was for the 2.6 g45b or g52b 2.0,pre 83 motor.
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  10. #35

    Array
    Status
    Offline
    Join Date
    06-01-2016
    Posts
    90
    Location

    Grand Forks BC
    Vehicle

    1985 Dodge Ram 50
    Engine

    I.D.K.?
    Great thread, starting my electric pump install to day.

  11. #36

    Array
    Status
    Offline
    Join Date
    10-29-2014
    Posts
    1,220
    Location

    Earth, the Solar System
    Vehicle

    1985 Dodge Ram 50
    Engine

    G63B
    Quote Originally Posted by rranger View Post
    Great thread, starting my electric pump install to day.
    Please post pictures for us slow readers

  12. #37

    Array
    Status
    Offline
    Join Date
    04-09-2016
    Posts
    47
    Location

    VA
    Vehicle

    1988 Mitsubishi Mighty Max
    Engine

    G54B
    Can anyone share what size or what parts are these as I need to do the same thing and I can't find anything that will fit in the oil pressure hole...everything I try even stuff that claims to be the right size will not fit... its mind numbing... Thanks

    Quote Originally Posted by mopar_ja View Post
    ok got some pics of the relay. Here is the relay i used http://www.summitracing.com/parts/SUM-890023/?rtype=10


    Attachment 2477 Attachment 2478 Here is pressure switches, left or top is safety switch for fuel pump other is just oil pressure. I put them up and angled for built in drain back feature didn't want switch(s) just sitting in oil, been working good so far.

  13. #38




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,851
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    the block is metric, the stub, t, and sensor/switch is 1/8 pipe thread. the block will need an adaptor to go from the metric thread of the block to 1/8 pipe thread.
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

Page 2 of 2 FirstFirst 12

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •