Results 1 to 16 of 16

Thread: Light bars & roll cages.

  1. #1



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,803
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6

    Light bars & roll cages.

    Is there any interest out there for some bolt together Light Bars for the bed of the truck, or bolt together Roll Bars for inside the cab? I was thinking about making a production run on some to fit 1st & 2nd gens. I would do the Light Bars first. I'm thinking a run of 5, at a time. They would be ready to send out to your local powder coaters or you can paint them. The tubing would be 1 1/2" OD 0.120 or 0.095 wall
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  2. #2

    Array
    Status
    Offline
    Join Date
    04-05-2011
    Posts
    210
    Location

    Portland, OR
    Vehicle

    1989 Dodge Power Ram 50
    Engine

    G54B
    i want one!! i want a light bar.

  3. #3



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,803
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    Quote Originally Posted by PowerRam348 View Post
    i want one!! i want a light bar.
    Should it attach to the bed or the the top edge of the bed sides??????? Whats your thought.
    Would you want bolt together or fully welded?
    If it aitches to the top rail of the bed sides it will be just a standard 4 point.
    If it mounts to the bed then. Would you want 1 vertical X bar. That would make it a 5 point VS a 4 point. I'm want to keep as much function of the bed as possible, while making it a one of a kind and useful in the unlikely event of a roll over.
    Last edited by camoit; 01-15-2012 at 03:28 PM.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  4. #4

    Array
    Status
    Offline
    Join Date
    04-05-2011
    Posts
    210
    Location

    Portland, OR
    Vehicle

    1989 Dodge Power Ram 50
    Engine

    G54B
    one that bolts to the inside of the bed for, like you said, the unlikely event of a rollover. and, yes, i would like the X bar. i'll take it fully welded as well too.
    Last edited by PowerRam348; 01-15-2012 at 12:11 PM.

  5. #5



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,803
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    How far back do you want the down bars to run? In front of the wheel well, or to the top center of the axle on the wheel well?
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  6. #6



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,803
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    After looking at it on the wheel well will look much better. In front just looks wrong.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  7. #7

    Array
    Status
    Offline
    Join Date
    04-05-2011
    Posts
    210
    Location

    Portland, OR
    Vehicle

    1989 Dodge Power Ram 50
    Engine

    G54B
    on the wheel well sounds good to me. i'm totally down for this.

  8. #8



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,803
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    I might have a finished unit for you when you come down if I get the time.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  9. #9




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,851
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    The 1st gen show bars from the factory bolted to the center of the wheel wells and the front corners of the bed with plates with bars tha fit the ribs of the bed. It would have been of no use in a rollover, as the bar was attached to sheet metal, but it was great as a tiedown bar for cargo.
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  10. #10

    Array
    Status
    Offline
    Join Date
    04-05-2011
    Posts
    210
    Location

    Portland, OR
    Vehicle

    1989 Dodge Power Ram 50
    Engine

    G54B
    i'm still cool with that. even if it isn't "functional" in a roll-over, it would make a great light bar and have a cool look attached to the inside of the bed. the ones that are connected to the bed rails are funky i think.

  11. #11



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,803
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    I should have it finished up tomorrow. It's raining so plenty of time to get her done. It should be some where around $100 or under when done. Did you want 4 lights or 2? If 2 did you want a "gaol post" on the inside of the light so you can throw long shit over the truck and not bust up the lights? So far I'm into it for $20 in trick tabs for the lights.
    You can see it live below.

    ANYBODY WANT A "U-WELD-IT" KIT??????


    Fire Fox Users may need to right click the screen for Start / Stop controls.
    Download? Right Clk, Then Save Target As
    Last edited by camoit; 01-20-2012 at 04:00 PM.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  12. #12



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,803
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    Last edited by camoit; 01-20-2012 at 07:20 PM.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  13. #13

    Array
    Status
    Offline
    Join Date
    04-05-2011
    Posts
    210
    Location

    Portland, OR
    Vehicle

    1989 Dodge Power Ram 50
    Engine

    G54B
    that's bitchin'!!!! looks nice

  14. #14



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,803
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    Got it, 2 lights, no goal posts. 4 bends. You might want to grab a tape and check the mounting plate width. It will fit in the back of the first gen so we should be good to go. I always wanted to do this in the camo truck but never got around to it.
    Now it looks bad ass...
    She is all tacked up. Once you give the word I'll finish it off.

    01-20-12_2111.jpg 01-20-12_2112.jpg

    ----EDIT----
    9" tall wheel wheel. top of rib to top of rib.
    35.5" tall from the top of bed rib to top of main hoop.
    55" outside to outside of hoop mounting plates.
    51.5" on center on the hoop.
    Down bars 51" On Center side to side.
    35" On Center front to rear.
    22.5 Deg inward angle on the top of the down bars..
    55" out side to outside of hoop mounting plates.
    31.75" light spacing On Center.
    If all is good then I will weld it up just as soon as you give me the OK.
    Last edited by camoit; 01-21-2012 at 06:43 PM.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  15. #15



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,803
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    Some minor adjustments need to be made. Other then that she looks good.
    Narrowing the outside to outside of the mounting plates to 55"

    01-21-12_1121.jpg 01-21-12_1122.jpg
    Last edited by camoit; 01-21-2012 at 12:55 PM.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  16. #16



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,803
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6

    Ready to go.

    Powerram, whats the inside measurement of your bed. I have 53.50" it fits, but it's a snug fit to the inside of the bed, on the first set of bends. If you have the bed liner it should still fit. We might just need to push it in.
    I made some adjustments to the fit it's at 53.25 at the lower bends. I gave it a rat coating of anti-rust paint on the bars. Ready for the final welding. Let me know if all measurements are good or if there is any adjustments that need to be made.

    Last edited by camoit; 01-21-2012 at 06:42 PM.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •