Page 2 of 2 FirstFirst 12
Results 26 to 41 of 41

Thread: Truck struggles under acceleration

  1. #26

    Array
    Status
    Offline
    Join Date
    01-29-2014
    Posts
    219
    Location

    Gilbert, AZ
    Vehicle

    1980 Plymouth Arrow Truck
    Engine

    I.D.K.?
    Quote Originally Posted by geezer101 View Post
    Blocked jets - try purging the carb. Engine running, cover the throats of the carb with one hand while opening the throttle. This will force the carb to pull excessive amounts of fuel through the jets and sometimes this is enough to unblock them.

    Suggested it on an earlier post on this thread.
    Well that didn't work. I guess I can take the top part of the carb apart and clear the nozzle that way...

  2. #27

    Array
    Status
    Offline
    Join Date
    01-29-2014
    Posts
    219
    Location

    Gilbert, AZ
    Vehicle

    1980 Plymouth Arrow Truck
    Engine

    I.D.K.?
    Hmm. Looking at this youtube video, is it possible that the other side shouldn't have a hole?

    https://youtu.be/jlEXR2hXUFg?t=163

  3. #28

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    4,392
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    It shouldn't as the accelerator pump jet should only feed the primary throat. It should have a nice steady stream of fuel coming out of it when its operating properly. You can see they're relatively easy to pull apart and you don't have to remove the entire carb from the manifold to work on it so if the accelerator jet is blocked, you can take it out and push some compressed air through it.
    support the forum that supports you - join and donate to MightyRam50.Net Get perks and donations $15 USD and over receive official MightyRam50.Net window decals

  4. #29

    Array
    Status
    Offline
    Join Date
    01-29-2014
    Posts
    219
    Location

    Gilbert, AZ
    Vehicle

    1980 Plymouth Arrow Truck
    Engine

    I.D.K.?
    Ok. I think my accelerator jet is fine then. Once I changed the gas cap & accelerator pump I get a good stream from the jet on the primary side.

    This leaves the fuel pump I think...

  5. #30

    Array
    Status
    Offline
    Join Date
    07-23-2018
    Posts
    119
    Location

    Seattle, WA
    Vehicle

    1988 Dodge Power Ram 50
    Engine

    G54B
    Here's a thread from a Jeep forum where a member has a Weber with the same no-load and with-load stumbling you're experiencing.

    https://www.jeepforum.com/forum/f12/...-opens-867114/

    Some of the replies mention possible causes, things to investigate and tests to try. I'd ignore suggestions to change jet sizes, especially if it ran fine before the hesitation problem appeared.

  6. #31

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    4,392
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    At this juncture I'd think about an electric fuel pump install which is always advised when doing a Weber swap. Depending on what pump you get, you can do this relatively cheaply and they're easy enough to rig up. Guys like the Carter P4070 fuel pump but I'm not a fan. They're expensive and noisy - plus I've had one fail on me (not only did it fail, but it caused issues downstream of the fuel pump when it coughed up a heap of fine brass shavings)
    support the forum that supports you - join and donate to MightyRam50.Net Get perks and donations $15 USD and over receive official MightyRam50.Net window decals

  7. #32

    Array
    Status
    Offline
    Join Date
    01-29-2014
    Posts
    219
    Location

    Gilbert, AZ
    Vehicle

    1980 Plymouth Arrow Truck
    Engine

    I.D.K.?
    So basically I need an electric pump, and a relay to kick the pump on when the ignition is on. Correct?

  8. #33

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    4,392
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    Yep. Use the hot wire that originally went to the carb as the trigger for the relay, and have the main power feed fused straight off the battery to the relay and out to the pump.
    support the forum that supports you - join and donate to MightyRam50.Net Get perks and donations $15 USD and over receive official MightyRam50.Net window decals

  9. #34

    Array
    Status
    Online
    Join Date
    01-09-2020
    Posts
    217
    Location

    Saluda SC
    Vehicle

    1987 Dodge Power Ram 50
    Engine

    G54B-T
    thats what i am doing, pretty simple and straightforward

  10. #35

    Array
    Status
    Offline
    Join Date
    03-16-2018
    Posts
    289
    Location

    Raymond New Hampshire, USA
    Vehicle

    1989 Dodge Ram 50
    Engine

    G54B
    I would hook a timing light up before you go to town on the carb. An ignition stuck advanced will cause sputtering and backfiring under load.
    The weber accelerator pump nozzle looks the same for both the 32/36 and 38/38. They use the same casting. The 32/36 only has a nozzle hole drilled on the primary barrel side however. It is normal for a 32/36 to only have one stream of gas. The 38/38 has both nozzles drilled. The speed at which you open the throttle determines the flow of gas. Open the throttle slow and it will dribble. Snap it open and you should get a stream. Failed accelerator pumps only cause momentary hesitation on throttle opening however. They bridge the gap between the idle circuit feeding the engine and the main circuit running the engine when you open the throttle.
    If it's fuel and not ignition, rough idle can be caused by fuel starvation or over fueling. Fuel starvation at idle, and there probably wouldn't be enough fuel to feed the engine running down the road. Rough idle and running caused by over fueling is usually smoothed out when you open the throttle.
    Acting fuel starved and over fueled makes me think the ignition system may be to blame. Can't hurt to check it out.

  11. #36

    Array
    Status
    Offline
    Join Date
    03-16-2018
    Posts
    289
    Location

    Raymond New Hampshire, USA
    Vehicle

    1989 Dodge Ram 50
    Engine

    G54B
    Somehow I missed the second page when I replied to this. One thought, a mechanical pump could be underperforming at low engine speed and overwhelming the carb at high engine speeds. So while it is possible that it is ignition like I thought, I would definitely install an electric pump as recommended. My truck came with a stock mechanical pump and a Weber installed. It ran much smoother when I went electric after the mechanical pump failed. But not before I replaced the mechanical pump and it failed again a few months later.

  12. #37

    Array
    Status
    Offline
    Join Date
    01-29-2014
    Posts
    219
    Location

    Gilbert, AZ
    Vehicle

    1980 Plymouth Arrow Truck
    Engine

    I.D.K.?
    I think I'll do the pump swap first, Giovanni, and see where that gets me. Hopefully all the way.

    Geezer is this the pump you recommend?

    https://www.ebay.com/itm/Top-Electri...n/292173987502

  13. #38

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    4,392
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    That's the one. I've bought that pump for my Weber install but I'm not ready to swap everything on my engine. This should (hopefully) solve your fuelling woes.
    support the forum that supports you - join and donate to MightyRam50.Net Get perks and donations $15 USD and over receive official MightyRam50.Net window decals

  14. #39

    Array
    Status
    Offline
    Join Date
    01-29-2014
    Posts
    219
    Location

    Gilbert, AZ
    Vehicle

    1980 Plymouth Arrow Truck
    Engine

    I.D.K.?
    I have some more questions... What is this thing here that the vacuum line is attached to:

    Click image for larger version. 

Name:	IMG_20200214_150255745.jpg 
Views:	11 
Size:	146.3 KB 
ID:	24397

    And what's this black thing in the red circle, and what's this vacuum line in the blue circle for?

    Click image for larger version. 

Name:	IMG_20200214_150307381.jpg 
Views:	12 
Size:	187.7 KB 
ID:	24398

  15. #40

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    4,392
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    The thing in image #1 is a vacuum triggered switch. It has come up before on the site and performs some kind of 'ignition on' circuit connection. A member had one fail recently and their truck wouldn't run. The thing in the red circle in image #2 is a vacuum barb cap that I think is part of the EGR system. Trace the vacuum hose in the blue circle to wherever it's going. It might be going to a control circuit or scavenging vapour/gas from the valve cover.
    support the forum that supports you - join and donate to MightyRam50.Net Get perks and donations $15 USD and over receive official MightyRam50.Net window decals

  16. #41

    Array
    Status
    Offline
    Join Date
    03-16-2018
    Posts
    289
    Location

    Raymond New Hampshire, USA
    Vehicle

    1989 Dodge Ram 50
    Engine

    G54B
    you'll have to follow the blue circle to find out where the hose goes. red circle, the cap is ported vacuum port. typically the vacuum advance on the distributor is hooked to ported vacuum. The lower hose is manifold vacuum port. some folks hook the vacuum advance to manifold vacuum. They are the same except when the throttle is closed. manifold vacuum when the throttle is closed provides a full vacuum signal. ported vacuum kills the vacuum signal when the throttle is closed. Personally, i find ported vacuum to be better. It provides better engine braking, and acts the same from part to wide open throttle. If your vacuum advance is hooked to the manifold vacuum, i'd recommend swapping the hose and vacuum cap.
    As geezer said, that vacuum switch prevented someone else's truck from running. You could unplug the connector, attach a jumper, and see if the truck will run.

Page 2 of 2 FirstFirst 12

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •