Results 1 to 12 of 12

Thread: New Stainless Steel Braided Brake Lines

  1. #1

    Array
    Status
    Offline
    Join Date
    09-24-2019
    Posts
    22
    Location

    Nevada
    Vehicle

    1991 Dodge Power Ram 50
    Engine

    6G72

    New Stainless Steel Braided Brake Lines

    Having nearly 30 year old brake lines on a truck is dangerous and makes for some spongy brakes. OEM rubber lines came with some fade from the factory as its inherent with all rubber lines. The advent of Braided Stainless technology has made it so your brake lines wont deform/fade under pressure and with the internal Teflon liners they last longer than you or I. Luckily I have access to the proper tooling, fittings and test equipment to make these lines.

    Decided to fix our 4x4 V6 Truck this weekend. Here is how we started with all stock minus the Gen2 Moni calipers.




    Luckily I dont live in the rust belt, so these came off pretty easily. Only one or two put up a fight.




    Some of you may not know this but the 4x4 Max uses 2 lines on each front wheel. Made each line, then pressure tested to over 3,000psi to exceed DOT spec. All passed.




    Two new lines for the front Passenger vs the two old lines.




    All plumbed up and installed on the fronts. Added new retainers as well.




    Tackled the rear axle next. Fabricated them about an inch longer to make sure I had additional room for flex. Quite a bit faster to do than the fronts.








    Wrapped it all back up, flushed out the old brake fluid, bled the system and took her out for a stroll. Brakes feel much better and firmer. I get greater feedback from the pedal and I also don't feel like i have to press as far, or as hard to get the brakes to start biting.

    For how inexpensive an upgrade this was its worth every penny. Sure, we all want to go faster, but do we think about how much faster we need to stop our vehicles? Also if any of us have swapped out the factory wheels and tires for bigger ones, your brakes now have to work harder and your truck takes longer to stop due to that added sprung weight.

    Anyways great upgrade all around.

  2. #2

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    4,259
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    Actually, brakes are a common topic here. The main request how to upgrade Gen 1 solid rotors and single piston calipers by swapping to Gen 2 brake and steering hub assemblies. Gen 1 brakes are 'adequate' until you push them hard, then they become a little scary. Luckily it's a nut and bolt swap to change them over. The other request for info is rear disc/axle swaps. This is a little more complicated as parking brake cables need to be modified and then there's the question of brake bias control.
    support the forum that supports you - join and donate to MightyRam50.Net Get perks and donations $15 USD and over receive official MightyRam50.Net window decals

  3. #3




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,803
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    what does a set of front and rear stainless brake line run for a 2wd 1980 D50?
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  4. #4

    Array
    Status
    Offline
    Join Date
    10-22-2015
    Posts
    348
    Location

    Nevada
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    Other
    Great write up and great looking product too! So are these DOT compliant then? And are you willing to sell kits? If so I would be interested in one for my 90’ 4x4.

  5. #5

    Array
    Status
    Offline
    Join Date
    09-24-2019
    Posts
    22
    Location

    Nevada
    Vehicle

    1991 Dodge Power Ram 50
    Engine

    6G72
    Glad to hear its a common topic. Yes, ive already upgraded to 2nd Generation Montero calipers and rotors for the front end. That upgrade was already a nice touch. Now that I have added the Stainless Braided lines its helped to firm up the brake feel even more. The added bonus is that I wont have to change these out ever again because the high quality materials are designed to last longer than you or I. I like that fact that the lines will take extreme off road abuse and it helps that they look very professional.

  6. #6

    Array
    Status
    Offline
    Join Date
    09-24-2019
    Posts
    22
    Location

    Nevada
    Vehicle

    1991 Dodge Power Ram 50
    Engine

    6G72
    Quote Originally Posted by pennyman1 View Post
    what does a set of front and rear stainless brake line run for a 2wd 1980 D50?
    Sure. My documentation goes back to 83-86 for Dodge, but some of my Plymouth info goes back to 1979 indicating it could be the same. Can you help me confirm your setup is identical?

  7. #7

    Array
    Status
    Offline
    Join Date
    09-24-2019
    Posts
    22
    Location

    Nevada
    Vehicle

    1991 Dodge Power Ram 50
    Engine

    6G72
    Quote Originally Posted by Chargerx3 View Post
    Great write up and great looking product too! So are these DOT compliant then? And are you willing to sell kits? If so I would be interested in one for my 90’ 4x4.
    Thank you. We try to make nice products for our customers. This was a side project, but if enough of you all are interested I can look into a production run?

    Charger I've already got yours figured out, so I would just need to know if you made any modifications to your truck height. How many inches lifted or lowered and have you swapped out any of the stock brake components like me for 2nd Gen Montero front Calipers?

  8. #8

    Array
    Status
    Offline
    Join Date
    10-22-2015
    Posts
    348
    Location

    Nevada
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    Other
    Great! I can’t say I’ve seen anyone else offer such a complete set. Are you going to do this for all the years and model configurations? I’ll pm you my info on my truck as it’s a little different. Also How many people would you need for a run?

    Im surprised more people don’t seem interested. I hope more join in.

  9. #9

    Array
    Status
    Offline
    Join Date
    09-24-2019
    Posts
    22
    Location

    Nevada
    Vehicle

    1991 Dodge Power Ram 50
    Engine

    6G72
    Happy to look into all years and makes (2wd, 4x4, ans so forth) for this platform. Actually you bring up a good point. I built my own lines partially because i have the specialized tooling in our shop to already do it to DOT requirements, but because there is nothing else out there.

    The more people the better for pricing. More requested sets, the better discounts I get on raw product.

    I could start a separate thread if that would better generate interest?

  10. #10

    Array
    Status
    Offline
    Join Date
    10-22-2015
    Posts
    348
    Location

    Nevada
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    Other
    Wanted to chime in.

    I received my 1990 Mighty Max V6 4x4 Lines in the mail last week. I ordered the Black lines with Silver Inserts because I like a stock look. I do have to say that I really like the build quality of these. Unlike other Chinese units that I have purchased for my other cars , these are sturdy and have some mass to them. Aren't they built here in the US too? They appear to be very strong and should outlast what off-roading I plan to throw at them.

    I had them extend my rear line to the axle 1 inch as i plan to flex it out a bit. I should have taken more pictures, but here are a couple. These are the front 2 lines for one side. You can see that they are quality and have aluminum sleeves vs rubber/silicon I've seen elsewhere.


    Click image for larger version. 

Name:	Max2.jpg 
Views:	8 
Size:	378.4 KB 
ID:	23724



    And here they are installed. Fit very well!

    Click image for larger version. 

Name:	Max.jpg 
Views:	11 
Size:	182.1 KB 
ID:	23725

    Thanks for offering this product! Now that I know these fit I would like to get another set for my other truck and possibly for my fathers as well. Is there going to be a group buy, or should I buy direct?

    Also would you be willing to branch out to other Mitsubishi models like say the 3000GT, Montero, Starion, etc?

  11. #11

    Array
    Status
    Offline
    Join Date
    09-26-2014
    Posts
    307
    Location

    Ca
    Vehicle

    1993 Dodge Ram 50
    Engine

    4G64
    Quote Originally Posted by B-Line View Post
    Happy to look into all years and makes (2wd, 4x4, ans so forth) for this platform. Actually you bring up a good point. I built my own lines partially because i have the specialized tooling in our shop to already do it to DOT requirements, but because there is nothing else out there.
    The more people the better for pricing. More requested sets, the better discounts I get on raw product.
    This public post is My order validation for 3 lines-- 1993 2x4 standard cab 4g64 5 speed.
    As I do not do payputz I will send You a Cashiers Check, after the $ clear send Me the lines.
    P/M Me your address
    Thx!!

  12. #12

    Array
    Status
    Offline
    Join Date
    09-24-2019
    Posts
    22
    Location

    Nevada
    Vehicle

    1991 Dodge Power Ram 50
    Engine

    6G72
    Chargerx3, I’m glad you like your new set of lines. Running a few inches longer wasn’t an issue either. They look good on your truck! And yes these are built here in the US using high quality DOT approved lines and fittings. You are right in that there are quite a few other lower quality Chinese knock offs out there. Be careful as some have been known to fail or not fit correctly and do not meet DOT standards. I appreciate your honest feedback.

    Im all for a group buy if we can get enough people. I think the savings would be worth it. I’ll look into starting a thread next week.

    I will look into other Mitsubishi vehicles as well. What are some models you all would like to see lines for?


    claych, you got it bud. I appreciate you reaching out. I’ll get working on your orders next week. I’ll send you a pm back with the details and a cashiers check is fine.

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •