Little red zip scooter out the door
paid $100 for it
new front tyre
patched the rear
new headlight bulb
new brake bulb
oil change
clean air filter
polish
reblack plastics
Tidy profit
sold to 2 ladies who want to be scooter buddies. I thought the one riding it home was the one that could ride. She pretty much right away whisky throttled it into the fence, stopping just short. Is now wobbling down the road in the dark. Terrifying tbh
at least the car will be following and its light traffic
Buy it back for $100 when they total it
support the forum that supports you - join and donate to MightyRam50.Net today! donations unlock the edit function
125cc suzuki twist and go i bought a while ago with no compression and no oil in it. piston, rings and a dingleball hone and i took it on a 10 day trip down to the top of the south island, and all over the 4wd tracks that adventure bikers tell me are so hard. Twist and go just twist and went, totally stock apart from a more knobbly front tyre (nothing would fit on the rear so thats just a road tyre), a 12v usb port, and a front rack for extra fuel
went really well, amazed, it only has 12cm of ground clearance and it was never an issue
had a couple of issues
the fan exploded for some reason. i was only just cruising along when it happend, so must have been damaged, or just old i guess. made some roadisde repairs and continued on with a vibrating bike.
eventually the seal on that side started leaking, probably the bearings are fine. But i bought another parts bike incase it makes bad sounds now. the baffles in the exhaust all came loose, and both the petcock and the press in float needle valve started leaking, so i swapped the carb and got a new petcock
now to sell - one lady owner, never thrashed
Thanks for sharing tortron ~ wife and me really enjoyed the beauty of your swell photos
Screenshot_20230320_215004_com.android.gallery3d.jpg
Screenshot_20230320_215011_com.android.gallery3d.jpg
Screenshot_20230320_215017_com.android.gallery3d.jpg
Here's my tiny house as of 1st of jan
Last edited by tortron; 03-20-2023 at 01:42 PM.
Screenshot_20230320_215409.jpg
Screenshot_20230320_215424.jpg
Went on a small bike ride during a weather event
Last edited by tortron; 03-20-2023 at 01:40 PM.
Screenshot_20230320_215646.jpg
Fixed this, so it's what I'm currently riding
Here's an Sr20de +t in my wingroad, all factory parts so its all bolt in, you just have to do some deep diving
Screenshot_20230320_215829.jpg
Needs a little more time spent on it, engine to come out and get new gaskets, and a few little bits. Weather has generally been terrible for months so haven't had a chance to do much
Last edited by tortron; 03-20-2023 at 01:39 PM.
"Ain't Life Grand"
Your tiny house is awesone ~ did you build most of it & if so well done tortron..!
Your motorcycle is cool too ~ is it a Yamaha 650cc or ?
Glad you're back posting ~ am hoping geezer has more time here as well...
Aloha ~ George
I built the whole thing except for the concrete pour and laying/connecting the sewer. I dug the foundation with a shovel and wheelbarrow lol.
Purple bike is a 1992 kawasaki zzr250, cheap because the guy couldn't get it running right. Turns out he replaced the carb manifold rubbers. Which is good, but it turns out the reproduction ones are a slightly different diameter and if you use the original clamps they bottom out just before getting tight enough to seal. So it always had a vacuum leak issue. I then had to reject as he had put bigger jets in to compensate. Goes great now. I actually bought a second one, also for cheap cos not running, that one was a pinched wire under the handlebar causing the main fuse to blow. Going to paint that one bright green as a kawasaki should be.
Several other motorcycles have come and gone. Here's one I got for my wife. Required the lower triple being bent back into alignment, apparently was big business for the dealers to replace them as they are very soft
Screenshot_20230322_210128_com.android.gallery3d.jpg
Screenshot_20230322_210146_com.android.gallery3d.jpg
I also did some work on my adv GN. Rebuilt the engine with 150cc kit, the piston was machined to have bigger valve pockets. Fitted a dr125 head which has considerably bigger ports, valves, and springs. It's an open combustion chamber type so unfortunately quite low final compression, and it's difficult to do any better with the supplied piston as its a poor shape for all applications (I don't know why they sell it). So although it has more power than stock, it was still kind of dissapointing off the line, then some stuttering around 7-8k rpm, both of which I think I could improve with a direct put pumper carb. But then it really ripped from 8 to 10000rpm. The big valves really work well with the big cam.
So for now I'm going to put a dr125 piston in a standard barrel and run a slightly higher compression ration than stock. I think that should be a good little ripper with the big cam for now, at least until I get to stripping a 6 speed bottom end and building a stroker
tortron you really get into mechanicals wow..! I am nearing my 75th birthday and dream about having a motorcycle (not smart) am held back from MC dream coz I only have a parking spot for our truck ~ would need ramps crane etc load offload device to keep the bike in the truck bed... I am happy to know you're still thriving thanks for sharing...
Keep Safe Bro
George
This turned into a bit of a - well, while I'm in there
Top points if you can guess what it's from
IMG_20230529_135049.jpg
I actually had an oops changing a $2 oring on the distributor. It has an offset drive so it can only go in one way........ Except it can go in the wrong way and then flexes the rear of the head and camshaft in an impressive way. Juuusssst bent the last exhaust valve enough that it would stick when warmed up. Oh well, got everything on clearance so that's cool, timing belt is due and got that for $12
BMW cylinder head ?
Who painted the trike bike ~ it's pretty now !!
Nope, not audi either.
I painted it. Candy apple red over silver flake and the white is snowflake pearl. The lettering is gold leaf too
Awesome painting Dude !
The cylinder head is from a Scotch Yoke Engine ?
hmm, doesn't look diesel or volvo,
Ahhhhh... Acura vigor 2.5 tl.
You have the same youtube recommended as meOriginally Posted by xboxrox
hmm, doesn't look diesel or volvo,
Ahhhhh... Acura vigor 2.5 tl.
Very close. It's a Honda ascot, with the 2L instead
I just noticed that the last cambelt 100,000km ago was installed wrong. They obviously set it up as a clockwise engine, but despite being a north south setup, this engine still rotates counter clockwise.
100,000km with the cambelt set at the 10degree btdc mark, impressive it only has 1 bent valve
Japanese market car only, but there's a few here, not so many now as the engine and gearbox layout was pretty unpopular with mechanics. So a lot more than should have got told nah can't fix mate
Very cool!!
2L 5cyl ! I bet that thing revs to the moon lol.
And I agree with xbox that trike paint is superlative!
Posting Permissions
Reply With Quote
Bookmarks