Results 1 to 6 of 6

Thread: TPS replacement on 94 2.4

  1. #1

    Array
    Status
    Offline
    Join Date
    11-07-2011
    Posts
    2
    Location

    Hephzibah,Ga.
    Vehicle

    1994 Mitsubishi Mighty Max

    TPS replacement on 94 2.4

    I'm replacing the TPS on my 94 2.4 mighty max. The sensor is slotted for adjustment. is there a procedure for getting it in the correct position? I'm new to the forum and this is my first post. Thanks for any help

  2. #2



    Array
    Status
    Offline
    Join Date
    03-26-2011
    Posts
    1,512
    Location

    Vacaville, CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    4G63-T
    On my eclipse engine you use a multimeter to either read the resistense between pins on the tps or check voltage at ecu. But I don't have a factory service manual for the 2.4 so I don't know the settings for it.
    Josh
    09 BMW 335i E92 Twin turbo
    89 Macrocab 4g63 Turbo swapped & Bagged: Build Thread

  3. #3



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,614
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    Did you try looking in the manuals and source information section. There might be a manual on your engine in there.
    Members come and members go, But the board keeps track of them.
    Check out the Fear Monger by
    clicking HERE.

    The MightyRam50 site is sponsored in part by On Site Concrete Inc.

  4. #4



    Array
    Status
    Offline
    Join Date
    03-26-2011
    Posts
    1,512
    Location

    Vacaville, CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    4G63-T
    Haynes manual says remove the connector on the TPS and measure resistance between terminals 1 and 4 on the TPS. Should be between3.5-6.5 K ohms. If out of spec replace. Then plug connector back in. Then check voltage at Pin 19 of ECU plug by connecting voltmeter red probe to Pin19, then black probe to Pin24(or any good ground). Should be anywhere from .48-.52V, clockwise rotation of TPS increases voltage, counterclockwise decreases voltage. There you go, how to set your TPS on your 2.4. It is actually the same settings as what my Eclipse TPS has to be set at
    Josh
    09 BMW 335i E92 Twin turbo
    89 Macrocab 4g63 Turbo swapped & Bagged: Build Thread

  5. #5

    Array
    Status
    Offline
    Join Date
    11-07-2011
    Posts
    2
    Location

    Hephzibah,Ga.
    Vehicle

    1994 Mitsubishi Mighty Max
    Thanks everyone the Haynes instructions worked great. Sure am glad I found this site

  6. #6



    Array
    Status
    Offline
    Join Date
    03-26-2011
    Posts
    1,512
    Location

    Vacaville, CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    4G63-T
    Awesome, glad to hear you got it adjusted correctly.
    Josh
    09 BMW 335i E92 Twin turbo
    89 Macrocab 4g63 Turbo swapped & Bagged: Build Thread

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •