Results 1 to 22 of 22

Thread: 4D55-T - I think my turbo's bad

  1. #1

    Array
    Status
    Offline
    Join Date
    04-03-2016
    Posts
    6
    Location

    Clearlake, CA
    Vehicle

    1984 Dodge Ram 50
    Engine

    4D55-T

    Unhappy 4D55-T - I think my turbo's bad

    I recently bought an 84 Ram 50 diesel and I'm started to do work on it. I just got my enormous California spec oil filter in the mail today so I got to work changing the oil. I pulled the inlet tube to the compressor to get access to the oil filter and I snapped some pictures of the wheel so I could see what condition it was in. Here is what I saw.





    This wheel is bent pretty bad. There's also oil marks on the bearing housing.
    Any advice? Rebuild, new turbo? I've heard of people putting Garrets on this engine.

  2. #2

    Array
    Status
    Offline
    Join Date
    01-18-2015
    Posts
    250
    Location

    Inwood WV
    Vehicle

    1991 Mitsubishi L200
    Engine

    4D56-T
    if you replace the turbo i want your hotside lol
    this is the same my td04-9b looked like after running 30psi and letting off throttle to fast, since you are tc05, you are non-wastegated, someone may have had fuel turned up and boost up at some point

  3. #3



    Array
    Status
    Offline
    Join Date
    07-24-2012
    Posts
    2,363
    Location

    Washington State
    Vehicle

    1986 Mitsubishi Mighty Max
    Engine

    G63B
    I guess you can't just re-bend those straight can you, lol. Looks like you sucked a bug in there.

    Do they sell new fans for turbos? or send it in for a rebuild. I would do some price checking to see which is the least costly and go that way.

    Welcome to the forum Sadied

  4. #4

    Array
    Status
    Offline
    Join Date
    04-03-2016
    Posts
    6
    Location

    Clearlake, CA
    Vehicle

    1984 Dodge Ram 50
    Engine

    4D55-T
    They're not bent. I spoke to my friend who's an experienced diesel mechanic, he says that's how impellers were made back in the day. The more you know.

  5. #5



    Array
    Status
    Offline
    Join Date
    03-26-2011
    Posts
    1,507
    Location

    Vacaville, CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    4G63-T
    What you really want to do to check if it is bad is to gently rock the shaft of the compressor wheel up and down and see if there is excessive play. There will be a tiny bit but you don't want a lot of play. And don't use a lot of force or you can wear out the bushing/bearings.

  6. #6

    Array
    Status
    Offline
    Join Date
    01-18-2015
    Posts
    250
    Location

    Inwood WV
    Vehicle

    1991 Mitsubishi L200
    Engine

    4D56-T
    Quote Originally Posted by Sadied View Post
    They're not bent. I spoke to my friend who's an experienced diesel mechanic, he says that's how impellers were made back in the day. The more you know.
    i seriously hope you are joking lol, if not you should unfriend him and recommend everyone avoid his shop.
    they were never produced bent

    On another note, yes the 10a wheel is still available, but i would recommend having it rebuilt. If it was on a gas motor i would say just swap the wheel, but the diesel turns the turbo higher rpm than the gas


  7. #7



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,803
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    It's true. Many of the first turbos were crude.
    Look at the Corvair. They looked like a coffee can connected to them.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  8. #8

    Array
    Status
    Offline
    Join Date
    01-18-2015
    Posts
    250
    Location

    Inwood WV
    Vehicle

    1991 Mitsubishi L200
    Engine

    4D56-T
    Quote Originally Posted by camoit View Post
    It's true. Many of the first turbos were crude.
    Look at the Corvair. They looked like a coffee can connected to them.
    if i recall correctly, those had the carb mounted on the front of the turbo, so fuel always spraying on the wheel, and non intercooled.

  9. #9

    Array
    Status
    Offline
    Join Date
    04-07-2011
    Posts
    275
    Location

    Burbank, CA
    Vehicle

    1983 Mitsubishi Mighty Max
    Engine

    4D55-T
    I am more worried about your oil filter. That is how the TC05-10a looks. That filter is an oem filter from before they painted them back in the 80's. Like most cheap 4d55 owners, it probably has not been changed in 50,000 miles and than they wonder why the engine is shot.

  10. #10

    Array
    Status
    Offline
    Join Date
    01-18-2015
    Posts
    250
    Location

    Inwood WV
    Vehicle

    1991 Mitsubishi L200
    Engine

    4D56-T
    Why do you think bent blades are how it is suppose to be?


  11. #11

    Array
    Status
    Offline
    Join Date
    04-03-2016
    Posts
    6
    Location

    Clearlake, CA
    Vehicle

    1984 Dodge Ram 50
    Engine

    4D55-T
    I just ordered that filter, I really hope it hasn't been sitting on a self longer than I've been alive.

    I'm getting mixed info about this turbo, I mean the blades just look wrong but there's no shaft play.

  12. #12

    Array
    Status
    Offline
    Join Date
    04-07-2011
    Posts
    275
    Location

    Burbank, CA
    Vehicle

    1983 Mitsubishi Mighty Max
    Engine

    4D55-T
    I have a bunch of those turbos. Seen them since 1992. Trust me.....

  13. #13

    Array
    Status
    Offline
    Join Date
    01-18-2015
    Posts
    250
    Location

    Inwood WV
    Vehicle

    1991 Mitsubishi L200
    Engine

    4D56-T
    Quote Originally Posted by mikewarme View Post
    I have a bunch of those turbos. Seen them since 1992. Trust me.....
    I trust you have a lot of abused turbos lol, the blades should never be going the wrong way lol, that moves air the otherway

  14. #14

    Array
    Status
    Offline
    Join Date
    04-07-2011
    Posts
    275
    Location

    Burbank, CA
    Vehicle

    1983 Mitsubishi Mighty Max
    Engine

    4D55-T
    Shit LOL he's right. I just went and looked at a few and they are not exactly like that. I guess my mind is playing tricks on me

  15. #15

    Array
    Status
    Offline
    Join Date
    01-18-2015
    Posts
    250
    Location

    Inwood WV
    Vehicle

    1991 Mitsubishi L200
    Engine

    4D56-T
    Quote Originally Posted by mikewarme View Post
    Shit LOL he's right. I just went and looked at a few and they are not exactly like that. I guess my mind is playing tricks on me
    Where is the like button lol. Thats why i am so confused as to why people are thinking the bent blades are normal lol.

  16. #16

    Array
    Status
    Offline
    Join Date
    04-03-2016
    Posts
    6
    Location

    Clearlake, CA
    Vehicle

    1984 Dodge Ram 50
    Engine

    4D55-T
    Okay, vanes sloped in the wrong direction doesn't make sense, I'm not an engineer though.

    I'm looking at some td04-09b turbos on ebay

  17. #17

    Array
    Status
    Offline
    Join Date
    01-18-2015
    Posts
    250
    Location

    Inwood WV
    Vehicle

    1991 Mitsubishi L200
    Engine

    4D56-T
    They will not bolt on unless it says 4d55 d56

  18. #18



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,803
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    I don't see it. They look to be going the correct direction. Looks like a CW rotation. the housing normally gets lunched before them fins move.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  19. #19

    Array
    Status
    Offline
    Join Date
    04-07-2011
    Posts
    275
    Location

    Burbank, CA
    Vehicle

    1983 Mitsubishi Mighty Max
    Engine

    4D55-T
    DO NOT BUY UNLESS THEY ARE FOR THE 4d55 or 4d56 and have same shape exhaust connection and do not buy 299.00 turbo from china. Will last only 5k or less

  20. #20

    Array
    Status
    Offline
    Join Date
    01-18-2015
    Posts
    250
    Location

    Inwood WV
    Vehicle

    1991 Mitsubishi L200
    Engine

    4D56-T
    Quote Originally Posted by camoit View Post
    I don't see it. They look to be going the correct direction. Looks like a CW rotation. the housing normally gets lunched before them fins move.
    Half of each blade is correct lol
    Quote Originally Posted by mikewarme View Post
    DO NOT BUY UNLESS THEY ARE FOR THE 4d55 or 4d56 and have same shape exhaust connection and do not buy 299.00 turbo from china. Will last only 5k or less
    They look similar but bolt pattern is different (3000gt uses a td04h 9b, will not work)
    Also I agree, no Chinese on a diesel, look up run away diesels lol.

  21. #21



    Array
    Status
    Offline
    Join Date
    07-24-2012
    Posts
    2,363
    Location

    Washington State
    Vehicle

    1986 Mitsubishi Mighty Max
    Engine

    G63B
    Not only are they bent, but they are bent unequally as well. Though I agree with Skullz, lol they are half right.

  22. #22

    Array
    Status
    Offline
    Join Date
    04-03-2016
    Posts
    6
    Location

    Clearlake, CA
    Vehicle

    1984 Dodge Ram 50
    Engine

    4D55-T
    I'm rebuilding it now, I'm sending the wheel/shaft assembly out to be balanced. The old comp wheel was definitely wonky.


    Attached Images

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •