Results 1 to 9 of 9

Thread: injector size?

  1. #1

    Array
    Status
    Offline
    Join Date
    10-11-2014
    Posts
    10
    Location

    Lakeland, FL
    Vehicle

    1991 Mitsubishi Mighty Max
    Engine

    Chevy V8

    injector size?

    what are stock injector size on the 2.4 ? wondering if a set i have are worth keeping for a project.

  2. #2


    Array
    Status
    Offline
    Join Date
    04-04-2011
    Posts
    712
    Location

    Columbus, OH
    Vehicle

    1992 Mitsubishi Mighty Max
    Engine

    Other
    175CC are stock units

  3. #3

    Array
    Status
    Offline
    Join Date
    03-11-2015
    Posts
    8
    Location

    Sturgis, MI
    Vehicle

    1994 Mitsubishi Mighty Max
    Engine

    4G64
    Are you sure they arent 275cc? Usually with other mitsu injectors, the ID mark is also the size. The service manual is showing the ID mark as N275H. Also, 175cc seems smaller than I'd expect for the hp rating of the engine.


  4. #4


    Array
    Status
    Offline
    Join Date
    04-04-2011
    Posts
    712
    Location

    Columbus, OH
    Vehicle

    1992 Mitsubishi Mighty Max
    Engine

    Other
    Yeah, my bad, 275's what was I thinking....holy thread resurrection

  5. #5

    Array
    Status
    Offline
    Join Date
    03-11-2015
    Posts
    8
    Location

    Sturgis, MI
    Vehicle

    1994 Mitsubishi Mighty Max
    Engine

    4G64
    Sorry for the resurrection. I was requested to by someone that was unsure which of us were correct. Thanks for the follow up.

  6. #6

    Array
    Status
    Offline
    Join Date
    08-11-2012
    Posts
    1,199
    Location

    Oakland, CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    G63B
    My whole world has been turned upside down.

  7. #7

    Array
    Status
    Offline
    Join Date
    08-11-2012
    Posts
    1,199
    Location

    Oakland, CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    G63B
    Is this too much injector for a 2.0 and a 2.4 computer?

  8. #8

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    6,059
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    I think it all comes down to what resistance value the injectors are. If you upsize your injector capacity, it 'should' only run rich until the ECU retunes itself to adapt to the new injector flow (which it should do fairly quickly).

  9. #9


    Array
    Status
    Offline
    Join Date
    04-04-2011
    Posts
    712
    Location

    Columbus, OH
    Vehicle

    1992 Mitsubishi Mighty Max
    Engine

    Other
    Incorrect, there is a value in the ECU firmware for the injector size, it need to match the ones being used, the ECU will not "adapt" to what is installed. It is making decisions based on sensor input and fixed values. it cannot compensate for major variations(I know, bummer).

    There a basically 2 kinds of injectors electrically, High impedance and low impedance. the 275's are High impedance, 450's (Stock Turbo) and larger are typically low impedance, hence the need for the resistor pack to compensate when switching types.

    Here's a site dedicated to Injectors

    http://www.robietherobot.com/storm/f...ectorguide.htm

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •