Page 3 of 3 FirstFirst 123
Results 51 to 68 of 68

Thread: More Power

  1. #51

    Array
    Status
    Offline
    Join Date
    04-24-2011
    Posts
    331
    Location

    Orlando, FL
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G64B
    I plan of using the h8 ecu out of a 2000-2004 mitsubishi eclipse, chryler sebring,dodge stratus, the jumper harness from mighty max to ecu is almost done

  2. #52




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,851
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    do you have a schematic of that - I am thinking of maybe doing a swap into the 86 project truck
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  3. #53


    Array
    Status
    Offline
    Join Date
    04-04-2011
    Posts
    712
    Location

    Columbus, OH
    Vehicle

    1992 Mitsubishi Mighty Max
    Engine

    Other
    Interesting, I used a AEM ECU for the Turbo Eclipse to get control of the timing and injector sizing etc... That why I eliminated the distributor and used the eclipse dual coil, igniter and Throttle body. IIRC I only had to add 2 wires and re-pin the ECU Plug to move some existing.... ben a while, that was in 08

  4. #54

    Array
    Status
    Offline
    Join Date
    10-26-2013
    Posts
    34
    Location

    Abingdon, VA
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    4G64
    I may have missed it somewhere, but what if any internal mods do you done to the motor and how many PSI do you think STOCK internals will hold reliably with your turbo?

    I am planning on turboing my 91 but wont be running alot of boost. I dont want to make alot of power, I just miss the sounds of a turbo since selling my turboed Probe GT and since I cant buy another one right now I figured I may just throw a turbo on the truck.

  5. #55



    Array
    Status
    Offline
    Join Date
    03-26-2011
    Posts
    1,507
    Location

    Vacaville, CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    4G63-T
    All stock motor I would run 5-6 psi MAX. You should be fine at those boost levels.

  6. #56

    Array
    Status
    Offline
    Join Date
    10-26-2013
    Posts
    34
    Location

    Abingdon, VA
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    4G64
    Sorry to post again but just had one more question. What is the best way to control fuel on a budget? Would I be safe just running the stock ECU with a adjustable or rising rate FMU with stock injectors to run around 5-6 PSI of boost and use a wideband to keep track of AFR? I have most of the other parts to piece together a turbo kit that I have accumulated over the years I just need to deal with fuel management as cheaply as possible now.

  7. #57




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,851
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    it is never a good idea to go cheap on fuel systems on a turbo motor - one lean out under boost and you can kiss the motor goodbye. Do it right and you will save money and your motor. Look for a megasquirt or other setup from a abandoned project car and use it to run the motor.
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  8. #58


    Array
    Status
    Offline
    Join Date
    03-21-2011
    Posts
    767
    Location

    WA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    4G63-T
    If you can find a apex safc and wire it in, might have the cheapest way to control fuel and add bigger injectors. What it does is modify the maf reading and adding or subtracting a value to increase or decrease fuel. Not the best but it's something.

  9. #59

    Array
    Status
    Offline
    Join Date
    12-21-2012
    Posts
    176
    Location

    North West Florida
    Vehicle

    1994 Mitsubishi Mighty Max
    Engine

    4G64
    For that low of boost, 4-5psi, I think fuel would not be an issue. But, never hurts to be prepared. I would swap all the stuff and run a dsm turbo ECU, that give you alot of room to play. I was ganna just start at 2-3 with a wideband and see how high you can go on a stock set up.

  10. #60



    Array
    Status
    Offline
    Join Date
    03-26-2011
    Posts
    1,507
    Location

    Vacaville, CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    4G63-T
    Quote Originally Posted by sleeps View Post
    I was ganna just start at 2-3 with a wideband and see how high you can go on a stock set up.
    That would be awesome if you could do that, I know tons of people want to know how much boost the 4g64 can take stock.

  11. #61

    Array
    Status
    Offline
    Join Date
    04-24-2011
    Posts
    331
    Location

    Orlando, FL
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G64B
    still working on the truck,got side tracked bought another turbo car, a 06 jetta gli for the misses,plan on taking the truck to the exhaust shop later this week

  12. #62

    Array
    Status
    Offline
    Join Date
    04-24-2011
    Posts
    331
    Location

    Orlando, FL
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G64B
    finished exhaust on the truck [IMG][/IMG]


  13. #63


    Array
    Status
    Offline
    Join Date
    01-16-2014
    Posts
    464
    Location

    Las Vegas, NV
    Vehicle

    1991 Mitsubishi Mighty Max
    Engine

    4G64
    I'm kind of curious why you didn't swap your TB over with a 60mm or even one with a better orientation?

  14. #64

    Array
    Status
    Offline
    Join Date
    04-24-2011
    Posts
    331
    Location

    Orlando, FL
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G64B
    I have a couple 1g eclipse throttle bodies that i can use,I just didn't want to use them until i have the patch harness for the h8 ecu
    Last edited by Rahtid; 02-09-2014 at 09:01 PM.

  15. #65

    Array
    Status
    Offline
    Join Date
    08-25-2012
    Posts
    160
    Location

    Winter Park, FL
    Vehicle

    1994 Mitsubishi Mighty Max
    Engine

    4G64
    Quote Originally Posted by Rahtid View Post
    Mitsubishi Starion 2.0 manifold from Australia,I paid $170 most of it was shipping.the guy i bought it from had a tubular manifold but i wanted the cast manifold to try out,
    A blacked out intercooler would look good,on my other car nobody notices the bigger intercooler when i'm at the track
    http://i138.photobucket.com/albums/q...ps7aed327c.jpg

    https://secure.buschurracing.com/cat...raceFMIC31.JPG for the sleeper look hoping for the same setup with the truck
    You frequent Speedworld as well?
    Attached Images

  16. #66

    Array
    Status
    Offline
    Join Date
    04-24-2011
    Posts
    331
    Location

    Orlando, FL
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G64B
    at least 2 time a month, I used to go every wed,fri, sat.

  17. #67

    Array
    Status
    Offline
    Join Date
    08-25-2012
    Posts
    160
    Location

    Winter Park, FL
    Vehicle

    1994 Mitsubishi Mighty Max
    Engine

    4G64
    Quote Originally Posted by Rahtid View Post
    at least 2 time a month, I used to go every wed,fri, sat.

    Interesting....How close are you, I'm in Winter Park. I was thinking turbo'in the 8v at some point as well

  18. #68

    Array
    Status
    Offline
    Join Date
    04-24-2011
    Posts
    331
    Location

    Orlando, FL
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G64B
    I live in deltona, but i'm always in orlando

Page 3 of 3 FirstFirst 123

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •