Results 1 to 2 of 2

Thread: took distributor out and put back in and now won't start

  1. #1

    Array
    Status
    Offline
    Join Date
    03-27-2012
    Posts
    120
    Location

    Bonney Lake, WA
    Vehicle

    1984 Dodge Power Ram 50
    Engine

    Please Select Your Engine Type

    Angry took distributor out and put back in and now won't start

    Where do I start to diagnose why it won't start? We had the same problem a few years ago when I got the truck and put it in the shop and they fixed it but wouldn't tell us what they did for $480. I"m thinking maybe I didn't have it all the way to TDC or my wires are not in the write spot so it's not firing right. Can anyone tell me the firing order for a 2.6L? Any info always helps.

  2. #2



    Array
    Status
    Offline
    Join Date
    07-24-2012
    Posts
    2,363
    Location

    Washington State
    Vehicle

    1986 Mitsubishi Mighty Max
    Engine

    G63B
    Wouldn't tell you what they did?? sounds like they did take your money though and whatever they did wasn't worth that amount. hmmm.
    Firing order 1-3-4-2

    Isn't your timing supose to be around 10 degrees BTDC? There should be a sticker under hood showing the timing of the vehicle.
    To line up distributor, place the crankshaft pulley at TDC and slide in the distributor so it seats pointing at the #1 plug cap wire. if this does not start the vehicle, you may have the distributor set incorrectly Turn the crankshaft pulley with a wrench, clockwise only and out of gear a full turn to TDC again and check the distributor again. Remove the distributor and repoint it at the #1 plug wire on the cap and try starting again. Remember to have a timing light handy so when it does start up, yu can properly time the vehicle to specs.
    Pulling the #1 plug out and inserting a finger in the hole will also locate true TDC. Installing distributor and seat with rotor pointing at #1 plug wire on cap. You can mark the distributor housing with a felt pen at #1 position also to help show placement without cap. If it backfires out carb or doesn't start, turn motor pulley around again and retry distributor placement again.

    Simple Test that can help diagnose starting problems.
    Each section is headed by the likely problem parts and followed by the noises/sounds you should listen for to determine if that is in fact the problem part. For all of these problems, you'll need to listen carefully when you turn the ignition.

    Battery/Alternator-
    If you turn the key and hear complete silence, your problem is most likely the battery or alternator. This means you are hearing no sounds at all, not even a sound suggesting an attempt of a start up. You can confirm one of these two parts as the problem by testing any of your electrical components in the car while the ignition is turned on such as radio, lights, windows, etc. If none work, then you've found your problem as the other problem parts wouldn't cause your electrical system to fail save for a short.

    Starter-
    If when you turn the key you hear what sounds like a grating/grinding sound, then this part is most likely the problem. The starter is what creates the initial electrical spark to get the whole system going. Try not to try more then 2 or 3 times if you hear a grinding sound as you can cause more damage.

    Fuel Injectors/Spark Plugs-
    You may have failing injectors or blocked up injectors if your car starts then sputters out, although a sputtering engine could also be due to low oil or a number of engine problems. These injectors carry the fuel to the engine where the fuel meets the sparks off of the spark plugs.

    Fuel Pump-
    Upon turning the ignition on, if you hear a noise from the rear of your car that sounds like any of the following: pressurized air gun, sucking, hissing, or a brief moving parts like sound followed by silence then your problem is most likely the fuel pump. The fuel pump is what takes the gas from your tank and pumps it through to your fuel injectors into your engine. A failed fuel pump can be due to the pump motor dying, low fuel levels, clog in the pump, or just an aged fuel pump.

    Fuses-
    A blown fuse can cause a no-start problem if the fuse that is blown is for one of the electrical components in the above list. You can use sight to check this problem by locating your fuse box and checking for fuses that are blackened or discolored.

    While there are many things that can go wrong in the complex workings of a car, the above parts are the most common culprits when your car just won't start. By being able to diagnosis which of the above parts is most likely the cause you can avoid diagnosis fees and extra hourly labor from a mechanic by telling your mechanic what you believe the problem is. Some good mechanics will even let a smart customer (one that can diagnosis their own car problem) go out and purchase the trouble part and will only proceed to charge the customer labor and not for parts. Money saving and looking smart to your mechanic aside, you'll impress your friends, feel good about your knowledge, and be able to say you know something about cars.

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •