Page 1 of 2 12 LastLast
Results 1 to 25 of 28

Thread: pinning cracked heads

  1. #1

    Array
    Status
    Offline
    Join Date
    12-07-2012
    Posts
    47
    Location

    lexington, ky.
    Vehicle

    1988 Dodge Power Ram 50
    Engine

    G54B

    pinning cracked heads

    I have a 88 d-50 2.6 with a cracked head between the valve seats. Has anyone pinned or welded similar cracks? What are the procedure and success rate?

  2. #2




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,851
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    all depends on the skill of the shop doing the work - you are much better off just buying a new clearwater or odessa head and putting your valve train on it - no jet valves and a better casting
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  3. #3

    Array
    Status
    Offline
    Join Date
    12-07-2012
    Posts
    47
    Location

    lexington, ky.
    Vehicle

    1988 Dodge Power Ram 50
    Engine

    G54B
    Can you plug the jet valves on the stock head?

  4. #4




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,851
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    yes - get a set of jet valve eliminators - they screw into the holes where the jet valves were
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  5. #5

    Array
    Status
    Offline
    Join Date
    09-30-2012
    Posts
    394
    Location

    Vanessa, Ontario
    Vehicle

    1989 Dodge Power Ram 50
    Engine

    G54B
    Sometimes even the most experienced shops can't weld a cracked aluminum head successfully. It has a lot to do with the casting itself. Cast aluminum is very porous and difficult to weld. Add to that the contamination that may be deep inside the crack and it becomes more difficult. I think when you add it all up, with the machining cost, if you do get it to weld successfully, you might as well buy a new head. I think Clearwater sells them for around $400 with valve train installed. Ready to bolt on, with a warranty.

  6. #6

    Array
    Status
    Offline
    Join Date
    12-07-2012
    Posts
    47
    Location

    lexington, ky.
    Vehicle

    1988 Dodge Power Ram 50
    Engine

    G54B
    Can you just plug up the jet valve with jb weld? Do you need to remove the jet valve cover that is on the inside of the head? How does it come out?

  7. #7



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,803
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    Quote Originally Posted by robertson5347 View Post
    Can you just plug up the jet valve with jb weld? Do you need to remove the jet valve cover that is on the inside of the head? How does it come out?

    NO JB WELD. There is a kit that eliminates them. You unscrew the stock ones and in goes in the eliminator kit.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  8. #8

    Array
    Status
    Offline
    Join Date
    12-07-2012
    Posts
    47
    Location

    lexington, ky.
    Vehicle

    1988 Dodge Power Ram 50
    Engine

    G54B
    Any comments on the next 2 questions. Do you need to remove and how the jet valve cover that is on the inside of the head?

  9. #9

    Array
    Status
    Offline
    Join Date
    03-21-2013
    Posts
    234
    Location

    Georgia
    Vehicle

    1984 Dodge D-50
    Engine

    4G63
    Not wanting to threadjack.......I have a question.

    What is the benefit of eliminating the jet valves?

    Where might you purchase these eliminating kits?

  10. #10

    Array
    Status
    Offline
    Join Date
    09-30-2012
    Posts
    394
    Location

    Vanessa, Ontario
    Vehicle

    1989 Dodge Power Ram 50
    Engine

    G54B
    Are you speaking of the little bump with the hole in it on the inside of the combustion chamber? You do not have to remove that. Do not use JB Weld on you cylinder head.

  11. #11

    Array
    Status
    Offline
    Join Date
    12-07-2012
    Posts
    47
    Location

    lexington, ky.
    Vehicle

    1988 Dodge Power Ram 50
    Engine

    G54B
    Yes, Many people seems to think the heat from this bulb type cover is what causes the heads to crack. Your thoughts.

  12. #12



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,803
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    Quote Originally Posted by mitchi View Post
    Not wanting to threadjack.......I have a question.

    What is the benefit of eliminating the jet valves?

    Where might you purchase these eliminating kits?

    They expand and contract at a different rate then the head, they also get stuck open or burnt and can lean out the cylinder. It's worth removing them to remove the problems they can create. It was a bad idea then and now. It was to make the engine spin the gas as it enters to clean up smog. Thats all. By eliminating them with the kit the head can expand at the same rate because there solid and not a hollow straw.


    http://www.silver-seal.com/product/6...L---Short.html


    http://www.racetep.com/starhead.html
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  13. #13

    Array
    Status
    Offline
    Join Date
    09-30-2012
    Posts
    394
    Location

    Vanessa, Ontario
    Vehicle

    1989 Dodge Power Ram 50
    Engine

    G54B
    It's not the little nozzle dome that causes the heads to crack. The jet valve assembly that screws into the head like a spark plug might ,but if that were true there would be a lot more cracked heads out there. They are made of steel while the head is cast aluminum. Steel heats up and expands slower than aluminum. It also cools and contracts slower than aluminum. When things that are fastened together expand and contract at different rates, things get stressed that's true.The little dome is aluminum and part of the casting so no real problem there. As Camoit said, the valves can stick open which can affect compression and mixture. The jet valve head also has a little passageway in it to supply the jet valve with its mixture from the carb. If you're going to replace the head I would use a non-jet valve head myself. I believe the biggest reason the heads crack is from overheating the engine. Cast iron block and aluminum head. Usually between the valves where the casting is thin on #2 or #3 cylinder.

  14. #14

    Array
    Status
    Offline
    Join Date
    12-07-2012
    Posts
    47
    Location

    lexington, ky.
    Vehicle

    1988 Dodge Power Ram 50
    Engine

    G54B
    Another question along these same lines with jet valves. On the #2 cyl. exhaust valve port, there is a hole. What is its purpose and does it need to be close off as well?

  15. #15

    Array
    Status
    Offline
    Join Date
    12-07-2012
    Posts
    47
    Location

    lexington, ky.
    Vehicle

    1988 Dodge Power Ram 50
    Engine

    G54B
    On the 2.6 g54b head. There is a passage from inside of the exhaust valve on the #2 cyl. which goes to the intake side. Does this needs to be closed if closing the jet valves? What purpose does it serve?

  16. #16

    Array
    Status
    Offline
    Join Date
    09-30-2012
    Posts
    394
    Location

    Vanessa, Ontario
    Vehicle

    1989 Dodge Power Ram 50
    Engine

    G54B
    I believe that is the EGR port. It does not need to be blocked off. You could clean it out if you wanted. If you have to pass an emissions test to get your registration you don't want that clogged up.

  17. #17

    Array
    Status
    Offline
    Join Date
    12-07-2012
    Posts
    47
    Location

    lexington, ky.
    Vehicle

    1988 Dodge Power Ram 50
    Engine

    G54B
    Thanks for the info. One other question, I need to use a head shim spacer .02" copper. Does it make any difference whether it's between the head and the head gasket or gasket and block? What do you use as a sealer on the shim and do you put the sealer next to the gasket side? I'm using a felpro blue stripe gasket.

  18. #18

    Array
    Status
    Offline
    Join Date
    03-26-2011
    Posts
    409
    Location

    Portland, OR
    Vehicle

    1986 Dodge Power Ram 50
    Engine

    G54B
    Quote Originally Posted by robertson5347 View Post
    Thanks for the info. One other question, I need to use a head shim spacer .02" copper. Does it make any difference whether it's between the head and the head gasket or gasket and block? What do you use as a sealer on the shim and do you put the sealer next to the gasket side? I'm using a felpro blue stripe gasket.
    May I suggest having a look at SCE gaskets? They make machined copper head gaskets for the G54B, but you have to have some patience as they are special order. You can get them in any thickness you need and they are reusable. They also aren't "cheap", but like a K&N filter, the extra you pay is because you probably won't be buying another.

    Their website has gone wonky, call and ask about them.

  19. #19

    Array
    Status
    Offline
    Join Date
    04-22-2012
    Posts
    22
    Location

    San Diego, Calif.
    Vehicle

    1982 Dodge Ram 50
    Engine

    G54B
    My '82 2.6 liter Ram 50, close to 190,000 miles , has been overheating/losing power when hot, such that I turn on the heater full blast, open the windows, and slow down from about 65 to 40 or even lower, when climbing to 6000 ft east of San Diego, in the late after noon in late spring or once in June, for recreations , abut once a month.

    When starting cold , seems that at least one cylinder is missing, (vibration) for 3 or 4 seconds, then smooths out with some more throttle.

    Muffler (?) rattle in reverse. Smog inspection coming up in August. Passed OK two years ago, with a new lower catalytic converter. I put replacement exhaust manifold on it about 3 or 4 years ago. Old one was cracked. Also cleaned off deposits on the upper cat ( or maybe I just removed the upper cat core).

    The head was resurfaced in Ensenada about 4 years ago. But later, the crank bearings scuffed when I overrevved for several minutes , via absentmindedly failing to go from second to drive on a long downhill.
    an obvious overheat. Crank and rod bearings fixed. Maybe I warped the head , again.

    Before that, mechanic in Ensenada said that valve clearances were correct. I have not set or checked the valve clearances myself for years.
    Maybe head bolts should have been retorqued after 1,000 miles , after the head resurfacing? But a bicycle collision complicated my life, and I did not drive for at least two years.

    Oil is full, coolant full, radiator should be healthy, with no rust or oil noted in coolant, which was regularly changed in years past. Have not checked the fan clutch

  20. #20

    Array
    Status
    Offline
    Join Date
    04-22-2012
    Posts
    22
    Location

    San Diego, Calif.
    Vehicle

    1982 Dodge Ram 50
    Engine

    G54B
    Somehow, I prematurely posted. Continuing:
    In the event that head /valve problems are diagnosed, have shopped online to see what a replacement head costs.
    Several sources list Taiwan replacement heads, said to be CAST IRON ????
    Is that an erroneous listing? Or, are there actually cast iron replacements for the original aluminum heads?

    If I plug the jet valve holes, when is going to be the effect on smog test? On performance? On mileage? Overheating Or, what might be some other effect, if any?

    On the flats, near the ocean, temperatures are normal for routine grocery shopping or other 5-15 mile trips. Thermostat was replaced about ten years ago. Have not tested the current one. Drove from 40, 000 to about 120, 000 (?) with a stuck or defective thermostat. With only VW experience, plus some Ford Escort misadventure ( bad module, a common problem with Escorts, before Ford began buying/ jointed with Mazda, which were much better, from experience until my sister crashed hers), I drove the D-50 and wondered why it ran so cool. A mechanic said " count your blessings". Maybe that contributed to the dirty condition noted in Tijuana when the Mikuni carb was cleaned at Carburadores Rodriguez, for a very low price by US comparison ( if a shop can be found yet who will do a cleaning and know Mikuni/Solex and are willing) .
    The powerful solvents used in Tijuana are hazardous to the workers, and probably banned in California.

  21. #21

    Array
    Status
    Offline
    Join Date
    09-30-2012
    Posts
    394
    Location

    Vanessa, Ontario
    Vehicle

    1989 Dodge Power Ram 50
    Engine

    G54B
    I would be suspect of the fan clutch for the overheating. Either way its an easy place to start and not expensive. Here's a bit of info on the jet valves....https://en.wikipedia.org/wiki/Mitsubishi_MCA

  22. #22

    Array
    Status
    Offline
    Join Date
    04-10-2011
    Posts
    256
    Location

    WA
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    6G72
    Recently read about an overheat caused by a partially clogged fuel filter, poster explained truck ran at normal temp up to about 50 mph but at higher speeds, engine overheated and died when speed was reduced. fuel filter replacement solved problem, idea being clogged filter caused lean condition. When was yours changed last?
    1990 MM 4x4 3.0
    1991 MM 4x4 3.0 Diamonte
    1994 MM 2wd (work in progress)

  23. #23

    Array
    Status
    Offline
    Join Date
    12-07-2012
    Posts
    47
    Location

    lexington, ky.
    Vehicle

    1988 Dodge Power Ram 50
    Engine

    G54B

    Check water pump. I bought my truck with overheating problem. After doing considera

    Check water pump. I bought my truck with a overheating problem. No circulating. After checking for blockages. Removed water pump and found the propellers were missing (rusted off).



    QUOTE=gordiray;41791]Somehow, I prematurely posted. Continuing:
    In the event that head /valve problems are diagnosed, have shopped online to see what a replacement head costs.
    Several sources list Taiwan replacement heads, said to be CAST IRON ????
    Is that an erroneous listing? Or, are there actually cast iron replacements for the original aluminum heads?

    If I plug the jet valve holes, when is going to be the effect on smog test? On performance? On mileage? Overheating Or, what might be some other effect, if any?

    On the flats, near the ocean, temperatures are normal for routine grocery shopping or other 5-15 mile trips. Thermostat was replaced about ten years ago. Have not tested the current one. Drove from 40, 000 to about 120, 000 (?) with a stuck or defective thermostat. With only VW experience, plus some Ford Escort misadventure ( bad module, a common problem with Escorts, before Ford began buying/ jointed with Mazda, which were much better, from experience until my sister crashed hers), I drove the D-50 and wondered why it ran so cool. A mechanic said " count your blessings". Maybe that contributed to the dirty condition noted in Tijuana when the Mikuni carb was cleaned at Carburadores Rodriguez, for a very low price by US comparison ( if a shop can be found yet who will do a cleaning and know Mikuni/Solex and are willing) .
    The powerful solvents used in Tijuana are hazardous to the workers, and probably banned in California.[/QUOTE]

  24. #24

    Array
    Status
    Offline
    Join Date
    04-22-2012
    Posts
    22
    Location

    San Diego, Calif.
    Vehicle

    1982 Dodge Ram 50
    Engine

    G54B
    I had water pump problems repeatedly, in decades past. It was the bearings . Repeatedly self-installed the Auto Zone "lifetime warranty" replacements. They were the lowest cost ones from Auto Zone, "reconditioned", as I recall. Finally, spent more as an increment to a higher quality replacement . No problems of which I know since that event, about ten years ago. I doubt that there is bad corrosion, unless the inhibitors listed in any decent coolant brand are not adequate.

  25. #25

    Array
    Status
    Offline
    Join Date
    09-30-2012
    Posts
    394
    Location

    Vanessa, Ontario
    Vehicle

    1989 Dodge Power Ram 50
    Engine

    G54B
    If the overheating is when you are going up long steep hills, perhaps dropping it into 2nd and getting the rpm's up will help.

Page 1 of 2 12 LastLast

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •