Results 1 to 9 of 9

Thread: Bolt pattern?

  1. #1

    Array
    Status
    Offline
    Join Date
    06-19-2012
    Posts
    96
    Location

    Hilo hawaii
    Vehicle

    1989 Dodge D-50
    Engine

    Please Select Your Engine Type

    Bolt pattern?

    92 montero same bolt pattern as a 89 ram 50?

  2. #2

    Array
    Status
    Offline
    Join Date
    04-06-2011
    Posts
    482
    Location

    Jacksonville, FL
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G54B-T
    bolt pattern is the same....but I believe the hole in the center of the wheel is slightly bigger on the montero

  3. #3



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,803
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    we have more info in the Wiki for you to look over.

    http://www.mightyram50.net/vbulletin...rossover+chart
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  4. #4

    Array
    Status
    Offline
    Join Date
    06-19-2012
    Posts
    96
    Location

    Hilo hawaii
    Vehicle

    1989 Dodge D-50
    Engine

    Please Select Your Engine Type
    http://www.jaos.com/preview.asp?catid=24 looking for this style rim in a 17 or 16 anyone know where I can find some similar?rim model (vectron super ziga)

  5. #5

    Array
    Status
    Offline
    Join Date
    06-19-2012
    Posts
    96
    Location

    Hilo hawaii
    Vehicle

    1989 Dodge D-50
    Engine

    Please Select Your Engine Type
    I also am looking for a rim that DOESN'T STICK OUT! What off set to I get?

  6. #6



    Array
    Status
    Offline
    Join Date
    03-26-2011
    Posts
    1,507
    Location

    Vacaville, CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    4G63-T
    Offset needed to tuck it going to depend on width of the rim. As the width goes up so does the offset in order to tuck. 7.5" wide +25-28 at the very least, usually +31. 8" atleast +40

  7. #7

    Array
    Status
    Offline
    Join Date
    06-19-2012
    Posts
    96
    Location

    Hilo hawaii
    Vehicle

    1989 Dodge D-50
    Engine

    Please Select Your Engine Type
    So basically a 17x8 would be positive offset 40 in order not to stick out pass the fender?offset just depends on width not hight of the rim?

  8. #8



    Array
    Status
    Offline
    Join Date
    03-26-2011
    Posts
    1,507
    Location

    Vacaville, CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    4G63-T
    If you want it just flush with the bedside you can probably get away with +25-30 or so but if you want it to tuck(clear the inner bedsides) then +40. Yes offset is only affectes by width

  9. #9




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,851
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    Original rims were 4.5" backspacing on a 6" rim. If you go to a wider rim, the same backspacing will work with no suspension issues with a stock setup (no drop spindles or drop coils, flipped ball joints, etc). When a dimension is given like +30 or +40 - that measurement is from the center of the wheel. A +40 rim that is 8" wide would have a backspacing of about 5.5". backspacing is always measured from a straightedge laid across the back of the rim to the back of the center of the rim mounting surface. Too much backspacing will cause clearance issues with suspension parts, or cause the tire to contact the inner fenderwells or strut rods.
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •