PDA

View Full Version : Weber jetting correct?



Mischif
10-12-2015, 03:02 PM
Okay so i finally got around to seeing what jets this thing has in it. Not sure if im gonna get the names correct but here it goes.
At the bottom of the bowl the primary fuel jet is 140, the secondary fuel jet is 155. On top of the carb/bowl (air jets??) The primary air jet is 170 and the secondary air jet is 160. Do those sizes sound good for a 2.0?

Background, truck runs rich around 16mpgs. Choke has been set, idle mixture adjusted, idle adjusted, float has been adjusted.

mopar_ja
10-12-2015, 07:17 PM
Lets start with, there is NO correct or incorrect jet settings. There is ONLY what works and what does not For You!
Based on but not limited to these conditions.

A. What model Weber you have.
B. Your Motor+Mods if any: Stock, Slightly Modified, Slightly Highly Modified
C. Your Location: Altitude, Temp. etc..

The only jets you did not list is the 2 most important Primary and Secondary Idle jets these, control your fuel from idle to about 3k rpm's where most of your driving occurs.

Do you have a tuning guide. Remember it is just a guide NOT gospel, use it as a staring point and either increase or decrease jet size for YOUR needs and it is always better to run a little rich than lean and burn a valve.

TIP 1. it is not a HOLLEY, CARTER etc..So it does not tune the same

TIP 2. If it stumbles, hesitates, falls flat, coughs it is usually A LACK OF FUEL

TIP 3. If while running and snap the throttle open a slight pause is all that should happen with a little puff out the exhaust.

TIP 4. Repeat Steps until Tip 3 is achieved.

Mischif
10-16-2015, 06:40 PM
Damn there's idle jets too? I'm gonna be an expert with this damn carb by time i get it running how i want. Alright thanks for the info, i'll have to check and see what size the idle jets are on it.

mopar_ja
10-17-2015, 07:40 AM
What Weber do you have 32/36 Progressive 38/38 Synchronized.

Mischif
10-17-2015, 04:27 PM
Its a 32/36 DGAV.

mopar_ja
10-19-2015, 08:26 AM
Primary Idle jet is depending how your carb is oriented behind the choke Big flat head secondary opposite side. (3a)

http://myarchive.us/richc/2012/6a052cebbaa3_DBC8/weber-carburetor-adjustment.jpg

geezer101
11-12-2015, 02:59 AM
Here are the the jetting sizes for a 32/36 DGAV relating to a 2000cc engine-

Main jet - (primary throat) 1.35
(secondary throat) 1.30

Air Correction - (primary throat) 1.75
(secondary throat) 1.45

Emulsion tube - (primary throat) F50
(secondary throat) F66

Idle jet (primary throat) 0.50
(secondary throat) 0.50

Idle air (primary throat) 1.50
(secondary throat) 0.70

*bearing in mind that the venturis are the right diameter for your engine, this is only a base line guide.
I've used 'primary' instead of the term 'progressive' - I think it's easier to understand. And the jetting seems to be too big for your engine, especially the main jets (the above chart shows the primary main being the bigger jet)

camoit
11-12-2015, 07:44 PM
progressive is how / type the secondary opens.

geezer101
11-12-2015, 09:47 PM
I have a suspicion that the figures on the jetting recommendations for the mains were recorded in the wrong order (I would find it weird that the primary would run a bigger main jet than the secondary). Looks like your 32/36 might have been jetted for a 2.6. Even so the 160 secondary main jet is BIG - should be 1.45/1.50 at the most for a G63B. Same goes for the air correction jet - go down to the correct size (the massive secondary main + air correction jet = dumping fuel). Change the secondary main jet and air jet and you should get mpg improvement and general top end power. Maybe upsize the primary air correction jet to 1.75 and you should get a bit more power down low. Have fun Mischif and let us know how this goes for you.

mopar_ja
11-13-2015, 07:48 AM
Also Don't forget all changes and adjustments should be made while trying to simulate driving conditions ie with air cleaner on it really does make a difference.

geezer101
11-13-2015, 12:26 PM
I ran into this last night in search of the formula to determine what is the best size venturi to suit a shared plenum intake (I came up bust but I did find out a lot of other useful info). This might have a link posted somewhere else but I'll chuck it in here - http://www.fordfe.info/CarbMythFact.html
The observations made in regards to carburettion aren't specific to an engine type or carb (he uses 2BBL vs 4BBL for comparisons of CFM) but if you're an engine NERD and are interested in the formulas to calculate ball park fuel delivery tuning then this will be very helpful.

He then goes onto header design and how that has a direct correlation to HP (air in - air out) and I know there are guys here who are onto R&D of their own headers so I also checked this out - http://www.superstreetonline.com/how-to/engine/turp-0611-custom-made-header/
(this went straight over my head - me and algebra are not good buddies) If I had the skills and time I would be all over this!

BradMph
11-13-2015, 10:19 PM
Weber does have basic rules also for weber carb adjusting. So many turns out, So many turns in and if it doesn't fall within this specification then you make jetting adjustments accordingly. In our manuals section of this forum, there is a weber manual dealing specifically with the weber. This may help you also. Depending on your elevation also can determine requirements in jetting.
I would do a basic check on how many turns that mixture screw is out and start there. The 170 seems a little off to me since I think I use about a 165 with headers, short dump exhaust, ported head and a race cam @ 2000 foot elevation, which elevation doesn't make a huge change, but it has some effects.

Mischif
11-14-2015, 11:33 AM
I still haven't gotten around to checking what size the idle jets are. I kinda pushed it aside since i got the truck running at about 26mpgs now. Interesting that you guys say it has bigger jets than what it needs. That would explain a few things. Doing anything over 70mph on the freeway and my mileage drops alot. Fast acceleration in the lower gears and it drops as well. Also it feels like the truck has no real power passed like 50% throttle and my best guess would be around 3krpm(no tach). Oil also still shows signs of fuel contamination. I'll have to give weber a call sometime next week and order some more appropriately sized jets.

mopar_ja
11-14-2015, 06:16 PM
3k is right around where secondary circuit takes over and runs to red line.

geezer101
11-14-2015, 06:44 PM
... it feels like the truck has no real power passed like 50% throttle and my best guess would be around 3krpm(no tach). Oil also still shows signs of fuel contamination. I'll have to give weber a call sometime next week and order some more appropriately sized jets.

Your engine is drowning in fuel (this carb may have been tuned for something like a 3.9 - 4 liter 6 cylinder) Jetting the secondary down will radically change how your truck performs and save your coin for other things (like that trick cam and tasty headers you're going to get in the future :grin:)

mopar_ja
11-14-2015, 07:21 PM
Just noticed, it wasn't asked or said what fuel pump / what are you running.

geezer101
11-15-2015, 12:47 AM
^good spotting mopar ja. No fuel pressure reg or not running a low psi pump will wreak havoc with the Weber.

yamahlr
11-15-2015, 03:38 PM
I run an AC EP42S electric fuel pump for many years. It was recommended by Top End Performance when I bought the carb. Been very happy with it. It is mounted by the fuel tank,below the tank on a little bracket that was already there.

mopar_ja
11-17-2015, 12:02 AM
This makes a world of difference Webers like fairly low pressure with higher flow/volume that is why i went with the Carter 4070 rotary pump.

And a side for a bit of fun and controversy Pumpernickel "IS THE BEST RYE BREAD EVER. PERIOD!"

Mischif
11-21-2015, 01:04 PM
Still haven't gotten around to checking idle jets or calling weber. Had some bad luck with the truck. Got in a dispute with a machine shop over some charges, walked away to go pull money out, and when i came back my key no longer wanted to go into the ignition switch. So after getting our shop tow truck to come pick me up i pulled the cylinder off. Looked like someone jammed paper in it. Then on the drive home my alternator finally gave out. Thing got towed twice in one day haha.

Anyway, my fuel setup is this. Some cheap 15 dollar electric pump off ebay. I think it was rated at around 4psi and 30 gph. When i tested it, it put out 8 psi. So i picked up a regulator and have that set at 3 psi.

This next week im really going to try and find the time to check those idle jets and also give weber a call about some jets.

pennyman1
11-21-2015, 01:24 PM
see how it runs now with the proper pressure and the mileage works out to. The jetting may be alright - too high a pressure will force the fuel past the needle and seat and flood out the motor.

geezer101
11-21-2015, 01:41 PM
...had some bad luck with the truck. Got in a dispute with a machine shop over some charges, walked away to go pull money out, and when i came back my key no longer wanted to go into the ignition switch. So after getting our shop tow truck to come pick me up i pulled the cylinder off. Looked like someone jammed paper in it. Then on the drive home my alternator finally gave out. Thing got towed twice in one day haha.

What a bunch of a-holes. If you send something into a shop to get it worked on and they run into an issue (whether its a part price issue or an unforseen problem that requires more effort and time), they should be ringing you first and asking where do you want to go from there. It is common courtesy. Then they sabotage your truck - in a really childish and pathetic act. The alternator dying is just another one of those things that fail without much warning but look on the bright side - you can get a replacement one with higher output now!

mopar_ja
11-22-2015, 06:19 PM
Sounds like time for BBB report and or Post on Rip off report and word mouth about their service. Might also want to check the flow on your fuel regulator, most of them work by restricting flow.

Mischif
11-25-2015, 04:28 PM
Finally pulled the idle jets. Primary is a 60, Secondary is a 50. How do those sound? So i was thinking instead of getting the right size jets how about i just add more air with a little snail :). Lol jk, well maybe...no i can't..hmm.

mopar_ja
11-25-2015, 07:48 PM
Those sound about right, also you adjust each side independently from each other.

elsupremo
12-12-2015, 09:17 AM
Many thanks to GEEZER. I set up my 32/36 Weber on 2.0 G63B with Australian headers using his jet settings.
As we say in Texas, "It's running like a lizard on a hardwood floor"!! Great power, smooth and getting much improved gas mileage.

ElSupremo






Here are the the jetting sizes for a 32/36 DGAV relating to a 2000cc engine-

Main jet - (primary throat) 1.35
(secondary throat) 1.30

Air Correction - (primary throat) 1.75
(secondary throat) 1.45

Emulsion tube - (primary throat) F50
(secondary throat) F66

Idle jet (primary throat) 0.50
(secondary throat) 0.50

Idle air (primary throat) 1.50
(secondary throat) 0.70

*bearing in mind that the venturis are the right diameter for your engine, this is only a base line guide.
I've used 'primary' instead of the term 'progressive' - I think it's easier to understand. And the jetting seems to be too big for your engine, especially the main jets (the above chart shows the primary main being the bigger jet)

geezer101
12-12-2015, 01:00 PM
Good to hear elsupremo. I pulled the jetting data from the 'WEBER CARBURETORS' bible by Pat Braden. It's an excellent resource manual and it contained a ready chart for the set up most commonly referred to for an upgrade on mightyram. What sort of improvement are you getting on your MPG?

elsupremo
12-13-2015, 08:06 AM
Good to hear elsupremo. I pulled the jetting data from the 'WEBER CARBURETORS' bible by Pat Braden. It's an excellent resource manual and it contained a ready chart for the set up most commonly referred to for an upgrade on mightyram. What sort of improvement are you getting on your MPG?

I ran the carb for almost a year using the jets that came with it. On the one long trip that I took staying at 55-60 MPH for about 350 miles each way I got a little over 29 MPG. Daily driving averaged 23-24 MPG. This is using regular pump gas containing ethanol.

I have yet to change the secondary emulsion tube from F50 to F66 and the primary idle jet from .60 to .50. With the other new jetting I have gotten a little over 27 average. That leads me to believe that I might get over 30MPG on a 55-60 MPH long trip. I have access to pure regular gas and might try some later just to see how much more improvement I can get with it.

pennyman1
12-13-2015, 11:55 AM
The thing to remember with E10 gas is that the ethanol leans out the mixture, requiring more fuel to compensate. If you run non ethanol fuel, it may run rich or be perfect. I am interested in your results, as I have the 86 project truck to get running again with a weber conversion.

geezer101
12-13-2015, 01:51 PM
You might find changing the emulsion tubes will have very little impact on performance. I would be tempted to say your current set up is close to perfect (if it is running the tiniest bit on the rich side it would be safe to leave it there in case you get into hills/mountains, towing a load or getting a tank of crap fuel). Using 97+ might not yield any big improvements on MPG but it'll run crazy smooth on it once you've tuned the engine to make the most of it.

Mischif
12-19-2015, 02:20 PM
Okay i was about to order the jets online, but i just wanted to be sure i get the correct ones.

Main jet - (primary throat) 1.35
(secondary throat) 1.30

Air Correction - (primary throat) 1.75
(secondary throat) 1.45

Those are what are recommended. However on the website the sizes are listed as .130, .135 ect. Not sure if i just ignore the decimals not being in the same place or if i need to convert from one unit to another to get the correct size. Anyone know?

geezer101
12-19-2015, 03:31 PM
Looks like they just screwed up the decimal place. They are using cm to convert (which is stupid of them not to identify those as the measured units) .13 cm = 1.3mm

The jet sizes are correct Mischif, so order to your hearts' content and get motoring! :layrubber:

Mischif
12-24-2015, 03:51 PM
Jets came in today!!! Just finished putting them in and readjusting the idle mixture, idle speed, and then mixture again. A little surprised at how much adjusting i had to do. With the old jets with everything dialed in i was getting 18ish" of vacuum, with the new jetting and everything adjusted im sitting just about at 20" of vacuum now. I replaced both air correction and main jets. I had ordered an idle jet to replace the .60 i have on the primary side but i ordered the wrong style :(. My weber uses the big style idle jet on the primary and then the small style on the secondary. Oh well i'm gonna drive it around for a bit and then decided if i want to go ahead and get the right idle primary or not.

Gonna go cruise and see what kind of difference i can tell.

Candler
08-15-2018, 01:22 AM
Anyone know why it lists two sets of air jets?



Thanks